Shopping Cart

Your cart is empty.

Your cart is empty.

93868 Spark and Sensor Electrode Replacement for Water Heater Parts 2-Prong

Free shipping on orders over $29.99

$9.90

$ 4 .99 $4.99

In Stock

About this item

  • Part No.: 93868, Package includes 1 x 93868
  • Spark Probe Single Sense 93868 for Water Heater
  • Fits: GCH6-4E, GCH6-6E, GCH6-7E, GC6A-7E, GH6-6E, GH6-7E, GH6-8E, G6A-6E, G6A-7E, G6A-8E, GCH6A-7E, GCH6A-8E, GCH6A-9E, GC6AA-7E, GC6AA-8E, GC6AA-9E, GCH10A-2E, GCH10A-3E, GC10A-2E, GC10A-3E, G10-1E, GH10-1E, G610-3E,GH610-3E, G10-2E, G10-3E, GC10-1E, GC10-2E, GH10-2E, GH10-3E, G6A-2E, GH6-3E, G6A-3E, GH6-3E, GH6-4E, G6A-4E, GCH6A-10E, GC6AA-10E, GC10A-4E, GCH10A-4E, XT 6 AND 10 GALLON SPARK IGNITION MODELS
  • If you are not sure how to install it, you can look up for a YouTube video how to change the parts, it's not hard at all
  • For any reason you are not completely satisfied, please feel free to contact with us


93868 Spark & Sensor Electrode Replacement Water Heater Parts
Condition: New
Package includes 1 X 93868

Fits: GCH6-4E, GCH6-6E, GCH6-7E, GC6A-7E, GH6-6E, GH6-7E, GH6-8E, G6A-6E, G6A-7E, G6A-8E, GCH6A-7E, GCH6A-8E, GCH6A-9E, GC6AA-7E, GC6AA-8E, GC6AA-9E, GCH10A-2E, GCH10A-3E, GC10A-2E, GC10A-3E, G10-1E, GH10-1E, G610-3E,GH610-3E, G10-2E, G10-3E, GC10-1E, GC10-2E, GH10-2E, GH10-3E, G6A-2E, GH6-3E, G6A-3E, GH6-3E, GH6-4E, G6A-4E, GCH6A-10E, GC6AA-10E, GC10A-4E, GCH10A-4E, XT 6 AND 10 GALLON SPARK IGNITION MODELS.


Claude Lanoix
Reviewed in Canada on June 10, 2024
bien heureux de l achat
Darlene Hood
Reviewed in the United States on April 3, 2024
Exact functional replacement, but the diameter of the mounting hole needed to be widened in order to use the mounting screw and mounting bracket of my water heater. Once installed, worked like a champ!
JR
Reviewed in the United States on April 26, 2023
Water heater would fire up and then immediately go out. If I put a propane torch on the tips of this device it would eventually stay running which told me this was most likely the culprit. This installs in 30 seconds with a pair of needle nose pliers. I'm up and running perfectly. Not all scenarios with my symptom will be fixed by this, but in my case it did the trick.
pflightnut
Reviewed in the United States on September 5, 2022
The spark and sensor electrode looked identical. Mounting it was not doable. Instead of a standard 1/4" hex head screw, a 7mm screw was in the package. Wouldn't have been a problem, but it wasn't self-tapping, & it was too large to screw into the existing bracket to mount the electrode. Re- using the original screw didn't work either because the mounting hole in the electrode was too small. So, I'll have to drill that out to re-use the original screw and hope it holds (with a bit of blue loctite). What a pain for something that should have been so simple.
Skip H
Reviewed in Canada on December 13, 2022
I had to change the end on it but that was easy and I was able to bend the flair end to fit better
#1 Jimmy
Reviewed in the United States on June 25, 2021
Works great
Marc Kaspar
Reviewed in the United States on May 15, 2021
Original part
Jake S.
Reviewed in the United States on December 30, 2021
Take your old one off and match it to the picture. It was a perfect replacement for mine. The original had the wire disconnect at the sensor end. For awhile, I could shove it back in to get it to work but that was getting annoying. The igniter/sensor sparks and then indicates that the flame lit. Mine would spark, light, then shut off, and repeat several times before it gave up. It pretty much ignites and stay lit now on the first try.
Mark
Reviewed in the United States on November 22, 2021
Easy installation on my Class A Motorhome Water Heater.
Robert K.
Reviewed in the United States on April 24, 2021
Exact replacement
Recommended Products