Your cart is empty.
Your cart is empty.
- Light color: Red Green Yellow
- Light type: LED, Flash light
- Buzzer: Yes
- For the display of operating status of machine tools, industrial machines, special machines, robots etc. suitable
- Weight: 548g
Pon Bear
Reviewed in the United States on February 19, 2019
See LG’s review for the wiring instructions, there are no wiring diagrams included, thamks to LG for his review,LG wrote”Had to buy it to figure out the wiring diagram. The wiring diagram on the box does not fully describe the wire detail. After testing, the box wiring diagram works, yet the lights a very dim except for the Green LED. The box also describes other light towers with other light colors (blue and white) and includes the wire colors. I couldn't determine which of the wire schematics to use as many were missing the same colored wires extending from the light tower.The box describes the wiring as follows:Gray with Red = dim Red LED lightGray with Orange = very dim Amber LED lightGray with Green = bright Green LED lightGray with Purple = Buzzer onFor best results for intended use, use these wiring configurations:CONSTANT ON wiring:Red (with Black wire paired) = Red is Power + for Red- (Negitive), Yellow- (neg), Green- (neg), and Purple- (neg)Red- is switched using Power- (ground) = bright Red LED light onYellow- is switched using Power- (ground) = bright Amber LED light onGreen- is switched using Power- (ground) = bright Green LED light onPurple- is switched using Power- (ground) = Buzzer on (buzzer is more like a high pitch tone like the high pitch keys on the piano... right hand side)Gray and Black wires = not usedINTERMITTENT ON wiring:Red (with Black wire paired) = Red constant Power+ and Black is constant Power- (ground)Red- switched with Gray wire = bright Red LED light flashing on/offYellow- switched with Gray wire = bright Amber LED light flashing on/offGreen- switched with Gray wire = bright Green LED light flashing on/offPurple- switched with Gray wire = Buzzer intermittent on/offGray wire = used as intermittent signal to groundAlso:Length (of light tower only): 12.250 inchesDiameter: 1.968 inches.Light tower base bolt thread: 16mm x 1.5mm with a contact thread depth of 15mm. A 5/8 inch diameter hole should be a snug fit for a mounting bore hole if not using the included hardware.Also there are mounting hardware 2 zinc plated steel thin nuts (16x1.5), a hollow aluminum tube 9.75+ inch, a zinc plated steel mounting angle bracket, and a zinc plated steel washer with a 16mm hole.The wires extend approximately 24 inches out from base of the light tower.Hope this helps anyone looking for these specifications for this light tower“
L G
Reviewed in the United States on April 1, 2018
Had to buy it to figure out the wiring diagram. The wiring diagram on the box does not fully describe the wire detail. After testing, the box wiring diagram works, yet the lights a very dim except for the Green LED. The box also describes other light towers with other light colors (blue and white) and includes the wire colors. I couldn't determine which of the wire schematics to use as many were missing the same colored wires extending from the light tower.The box describes the wiring as follows:Gray with Red = dim Red LED lightGray with Orange = very dim Amber LED lightGray with Green = bright Green LED lightGray with Purple = Buzzer onFor best results for intended use, use these wiring configurations:CONSTANT ON wiring:Red (with Black wire paired) = Red is Power + for Red- (Negitive), Yellow- (neg), Green- (neg), and Purple- (neg)Red- is switched using Power- (ground) = bright Red LED light onYellow- is switched using Power- (ground) = bright Amber LED light onGreen- is switched using Power- (ground) = bright Green LED light onPurple- is switched using Power- (ground) = Buzzer on (buzzer is more like a high pitch tone like the high pitch keys on the piano... right hand side)Gray and Black wires = not usedINTERMITTENT ON wiring:Red (with Black wire paired) = Red constant Power+ and Black is constant Power- (ground)Red- switched with Gray wire = bright Red LED light flashing on/offYellow- switched with Gray wire = bright Amber LED light flashing on/offGreen- switched with Gray wire = bright Green LED light flashing on/offPurple- switched with Gray wire = Buzzer intermittent on/offGray wire = used as intermittent signal to groundAlso:Length (of light tower only): 12.250 inchesDiameter: 1.968 inches.Light tower base bolt thread: 16mm x 1.5mm with a contact thread depth of 15mm. A 5/8 inch diameter hole should be a snug fit for a mounting bore hole if not using the included hardware.Also there are mounting hardware 2 zinc plated steel thin nuts (16x1.5), a hollow aluminum tube 9.75+ inch, a zinc plated steel mounting angle bracket, and a zinc plated steel washer with a 16mm hole.The wires extend approximately 24 inches out from base of the light tower.Hope this helps anyone looking for these specifications for this light tower.
Recommended Products
$160.36
$ 75 .99 $75.99