Your cart is empty.
Your cart is empty.Product Description
カスタマー
Reviewed in Japan on November 10, 2024
デザイン、明るさは申し分ないのですが、装着してしばらく走ると、ヘッドライト内が曇ってきて、結露してしまいました。様子を見たら改善されるかと思ったのですが、同じ状況が続いています。電装品だけに、水気は大敵です。状況が変わらないようであれば、ノーマルに戻そうかと思います。冒頭でも言いましたが、デザイン、明るさはとても良いだけに、残念です。
Juan José Moreno Saenz
Reviewed in Mexico on October 7, 2024
No enciende al parecer defectuoso de fabricación…
ktmracer64
Reviewed in the United States on July 25, 2023
Seems like most of the reviews on here are pretty positive and i would agree. Bought this for my FE350S.+ve: Very easy to install, brighter than stock, looks better than stock (IMO), appears to be of good build quality as well.-ve: slightly heavier than stock (i would say about 0.5lb)The pictures don't necessarily do it justice. The LED (pic on the left vs. stock on the right) definitely makes it brighter. Perhaps not super significant but for $60 i'd say its pretty good. And as i said above i do like the looks of the light way better than stock. It's probably a ways off from a baja designs light but then you are saving quite a bit of money.For install, I switched the wires on the main plug itself. It was easy. I squeezed the tab with a small/thin long needle nose plier and was able to push out the wires. Just bend out the tab again slightly before reinserting. You can figure out the wiring by looking at your stock light. The color wire that runs to both the lower and upper bulb will be your ground. The other wire running to your lower bulb will be the DRL. Then the low/high beam wires you can either guess/swap or use a volt meter.I actually wired the included jumper cable to disable low beam and DRL for offroad riding. So i can easily and quickly plug in the jumper cable for riding off-road and my light will be entirely off when the switch is on low beam. But high beam will still work. So basically, i only route the ground wire and high beam wire in the jumper. To be honest, I actually spliced the DRL to the high beam wire. So on high beam i have all lights on, including DRL.If i am to do street riding which is seldom i can quickly unplug the jumper and everything will work as required for street use.Why did i do that? When riding off-road most of the time i don't want the light to be on. I am also a little worried about draining the battery when i am out in the middle of nowhere. Call me paranoid.The only thing i can't comment about is the reliability of the light. If that turns out to be a problem, i'll update here.
Gustavo Zimbron Lara
Reviewed in Mexico on June 6, 2023
The media could not be loaded.
Tony
Reviewed in Australia on June 17, 2023
Great product good service
Kyle P.
Reviewed in Canada on March 27, 2023
Great upgrade over the OEM... this is a quality feeling, heavy light. Super bright! Worked well with my 2023 Husqvarna TE250, used the supplied wire to make it work, both whites are positives on the US versions of the TE's. Sharp looking light!
Max
Reviewed in the United States on February 16, 2023
The media could not be loaded.
C Ray
Reviewed in the United States on October 26, 2022
I wanted to take the time to write a review for this light because I think it's a great product at a great price!This headlight is a significant improvement over the stock headlight in every way. The light output is substantially brighter than the stock halogen bulb and I have it wired currently for low beam and running light only. I don't have a way to control the high beam on my bike (yet) but could have easily wired it to have the high beam on at all times when the headlight is on. It comes with everything needed to install including all the necessary hardware and a subharness to make it truly plug and play. It appears to be high quality and very well made. You absolutely cannot beat this light for the price.I opted to not use the sub harness and instead released the pins in the LED headlight plug and oriented them to fit the plug on my Husky. Very simple and worked well for me.You will not be able to use your coarse thread screws that hold the top of the factory light to the shroud but instead will use the supplied screws and washers to hold the new light to the shroud. I opted to use a little loctite to prevent the screws from vibrating loose.I give the light 5/5 stars and am very much looking forward to having an actual headlight that provides some actual light!!! It not only looks good on the bike but it throws some light. I highly recommend. You will not be disappointed.
Recommended Products