Your cart is empty.
Your cart is empty.Heavy-duty differential covers and transmission pans provide increased lubricant and cooling capacity for hard-working recreational and utility vehicles. Mag-Hytec covers and pans set your vehicle apart in both aesthetics and function: cast from A356-T6 aluminum and textured black powder coat with machined cooling fins. Magnetic drain plugs trap worn gear material promoting fluid integrity. Each unit is equipped with ARP 568 O-rings for superior sealing. All hardware is 303 stainless steel, no gasket or sealant is required in most applications, and all Mag-Hytec parts are covered by a limited lifetime warranty. Depend on Mag-Hytec when you're pulling a heavy load. Avoid costly recapirs - Extends the life of your vehicle - Expands oil capacity - Runs cooler, lasts longer Average double the fluid capacity Ease of service Dipstick is knurled for quick removal, flat is marked low/high to check the lubrication level and a magnet, which acts as an open filter is at the bottom end. The MS 7/8 - 14 THD port is large enough to be used for filling. The magnet filled drain plug is the same MS port as the dipstick. Both the dipstick and drain are O-ring sealed. The sending unit fitting is 1/8 THD tubing and with a stainless tube plug. The calibration plug is centered on the serial number plate and approximates the stock cover fill plug for the factory fluid level. The O-ring snaps into the inverted "V" groove for a positive seal without gasket or silicone. Plugs, screws and washers are stainless steel in most applications. Mag-Hytec makes the best covers and pans available today.
Kindle Customer
Reviewed in the United States on March 26, 2024
Perfect fit on my 06 with upgraded steering. Really close but no rubbing. Just what I wanted and perfect match for the rear too. Just get it!
Bryan Guchereau
Reviewed in the United States on July 6, 2021
Easy install, kinda pricey but already had the rear cover.
Brian Kellogg
Reviewed in the United States on January 27, 2021
Looks great in the box. If you have a 2012 Ram 2500, it won't clear the OEM steering stabilizer, even if you cut down the U-bolts. Installed it, looked like it should clear, and one day of driving later it has abiut a 2" gouge out if it. The company says the clearance issue was addressed, well that's obviously incorrect. They also acknowledge that it may not fit, bit if it doesn't, it isn't their fault (says nothing about fitment issues in the package, you have to hunt it down on their website). Positive note: It doesn't leak, and looks good if you aren't real close.
rod
Reviewed in the United States on April 25, 2021
Not very easy to install, it is a very tight fit getting in in. But it us build like a brick house...
tom
Reviewed in the United States on January 16, 2020
I have a 2004 Dodge Ram 5.9 diesel. The cover fit perfect. Holds four quarts instead of 2. Had to jack up the frame on the drivers side to get to the top bolts on the diff cover. Swing arm blocks the bolts. Other than that, no rubbing when turning right or left. Perfect!
Chris Zee
Reviewed in the United States on June 5, 2018
The fit and finish on this piece is outstanding.Well engineered, fit perfectly. They even give you a extra bolt just in case. Gotta love a company like that.
jrk93
Reviewed in the United States on December 3, 2018
2012 Ram 3500 4wd. Steering stabilizer u-bolted bracket came in contact with cover before full lock to left. Had to trim bracket to get it to clear. Not an issue if you’re mechanically inclined. Very stout cover, stainless hardware and O-ring gasket.
jon
Reviewed in the United States on April 21, 2018
Fit great on my 06 ram 3500. No interference. Took 4 qts on a over night drain. Comes with a very good gasket. Looks good. Gits good.Bought the rear and trans pan also.
Recommended Products
$125.95
$ 54 .99 $54.99