Your cart is empty.
Your cart is empty.Product Description
Cable Box Wall Mount, VESA Mount, Under-Shelf Mount for DISH Wally Receiver
Mount your DISH Wally receiver in your RV, camper or boat with the HIDEit Wally Receiver Mount. The Wally Mount is the perfect way to free up valuable shelf space. Custom wrap design won’t block Wi-Fi, buttons, or DISH Smartcard. Our unique coax channel ensures a secure fit, so the device won’t move around. The mount is easy to install and can be VESA, under-shelf, or wall mounted to fit any space.
- VESA Compatible: 100mm + 200mm (M4), single M4 + M6.
- Coax channel "locks" Wally in place while in motion.
- Easy access to ports, buttons, and the DISH Smartcard.
- Doesn't interfere with RF sensor. Test location before setup.
- Made in USA from 16-gauge, cold-rolled steel for durability.
- Powder coat finish protects from scratches.
Keep your DISH Wally safe while you're on-the-go with the HIDEit Wally Mount!
- (1) DISH Wally Mount - Made in USA
- (2) #8 Flat Head Drywall Screws
- (2) Drywall Anchors rated for 25 lbs each
- (2) M4 Screws
- (2) M6 Screws
- Copyright Registration: VA0002300916
OTHER HIDEit MOUNTS PRODUCTS YOU MIGHT LIKE
Si
Reviewed in the United States on February 7, 2025
Good product. It fits. It's metal, not plastic
Bob
Reviewed in Canada on February 17, 2025
It was bent slightly as it came just in a bag, but bent back ok and is sturdy enough to hold Sat [ Dish ] Wally Reciever . It looks good tooBut it has a metal segment as as wide as your finger that does not support anything , might be there to stop the box from sliding out the back? This metal bit stops poss of plugging in one-2 reciever ports ,for sure no Ethernet cable could be plugged in unless you cut off the metal segment ( or make it very thin)But the reciever its very tight in it , can bend it if want ever slightly so box won't move . But they could have bent wrap around ends to hold it , it sort has has ?
Jack D
Reviewed in the United States on September 20, 2024
This was the perfect solution for mounting our Wally to the entertainment center wall in our RV. Solid and a perfect fit for the receiver.
Kerry Gwin
Reviewed in the United States on July 6, 2024
Perfect size, mounted my walley in my truck, just right, it’s mounted securely and out of the way.
Terry nolan
Reviewed in the United States on June 11, 2024
Product seems to be a good quality and works well
Joe
Reviewed in the United States on December 7, 2024
I have mine velcro'd to back of a 32" LED TV. When the Wally is pre-wired to hard disk and TV, all I need to do is mount TV to wall mount (to heavy to leave on while on the road), hook up antenna and 2 power cords and I'm ready to go.
james crousore
Reviewed in the United States on October 19, 2024
The easy to install and putting the receiver in the bracket.
Customer
Reviewed in the United States on October 18, 2024
I like the fact this is a custom built mount specifically for the Dish Wally, and the fact it's American made. I recently installed one in my RV and this allowed to mount the Wally vertically on a wall behind the TV.It's very strong steel and holds the Wally firmly. The little tab that the coax port fits in actually acts like a bulkhead fitting when you install the coax, locking it in securely.I have absolutely no complaints, but do have some observations and suggestions. You must use a flat head bolt or wood screw to mount this bracket, and can't use anything larger than a #8 screw/bolt. The receiver absolutely won't fit if there are any screw heads that aren't flush with the base of the bracket; the fit is that tight. I would also like to see a couple more countersunk screw holes in the base. In an RV, they take quite a beating during travel.
Hild
Reviewed in the United States on July 31, 2023
Best and affordable solution to hide all your wires and wally box. As the wally remote uses RF, you don't even need to point the box on the back with the remote.
Recommended Products