Your cart is empty.
Your cart is empty.Product Description
2 in 1 handheld vacuum pump
2 in 1 handheld vacuum pump
Easy to use: just select the intake control valve on the pump for the output of the pressurizing system / the input for testing the vacuum.
2 in 1 handheld vacuum pump
2 × 4oz liquid storage tank
The supplied liquid storage tank facilitates oil transfer and ensures clean operation
2 in 1 handheld vacuum pump
Alumina-proof pump with pressure gauge and extended nylon handle for easy use··
14PC Adapter
Different adapter nozzles for most vehicles
Portable Brake Tool Box
Vacuum hose
The transparent hose helps to observe the discharge of the waste liquid··
Portable Brake Tool Box
Portable Brake Tool Box
Brake Bleed Sleeve Vacuum Gauge with Robust Blow Molding Housing for Easy Storage and···
Widely used
Widely used
Wide range of use: vacuum pump tester can test many vacuum operation system
Suitable for a variety of automotive test and diagnostic tasks, including brake bleed, vacuum and pressure pumps to generate and maintain metering vacuums, for testing a wide range of automotive, marine, aircraft and agricultural equipment.
Paul
Reviewed in the United States on May 9, 2025
Tiene buena fuerza de succión
BRIZZI
Reviewed in the United States on March 30, 2025
Well made, arrived quickly, used it to bleed brakes on my car and it worked great. Very pleased with it.
Blue sky
Reviewed in the United States on March 12, 2025
Ok. It sure get if work couse im still not use it
Stretchnutz
Reviewed in the United States on April 30, 2025
Good for bleeding brakes and pressure testing chainsaw carburetors
DN
Reviewed in the United States on April 27, 2025
This is not a brake bleeder, it pushes air out, not a vacuum pump for bleeding brakes on a motorcycle. DO NOT BUY if that’s what you’re using it for. One star for customer service. I contacted that and never got a response!
steven pounder
Reviewed in the United States on April 2, 2025
Product is built to a price point so for an occasional weekend DIY mechanic the product works just fine. I didn’t buy it to bleed brakes however. I use it to set my wastegate actuator, boost solenoid functionality as well as test the vacuum system for leaks etc. For those that are having trouble with having enough force to bleed brakes or power steering pay attention to your tubing ID and total length. To much hose just adds to the amount of volume the pump has to deal with. Also make sure you have enough fluid in the system to bleed. You can run in to situations of max pressure or vacuum but not enough fluid to reach your desired destination. Gauge seems accurate as it reads the correct total vacuum of the engine mounted vacuum pump. It’s cheap but does the job.
Luis Angel
Reviewed in Mexico on May 17, 2024
Pensé que sería mejor, la verdad esperaba más de esta herramienta, no tiene la suficiente fuerza como para purgar el sistema de frenos, solo sirve para sacar un poco de líquido viejo de los depósitos 2/5 estrellas.
R.MARIN
Reviewed in the United States on October 3, 2023
Not a cheapo. IOPS for sure. The pump is strong as I used it to pump brake fluid out from the brake bleeder screw. Hand for a bit tired but I was expecting that. Did a complete brake fluid change in my Mustang in about two hours. It’s a trick to get the rubber fittings to keep a strong seal but it doesn’t have to be perfect. Some air will pull into the pump anyway. Just keep going. Cleans easy and fits nice and neat in the casr. The case was great for me because if it didn’t have it, the room would be thrown in the tool bag I call the land of the misfit sockets. Yup, I’m messy as hell and don’t give a crap about taking care of stuff , unless it’s in a case then I will. So I’ll update when I use it again, for the gf’s car.
Barry
Reviewed in the United States on January 22, 2023
Its a nice kit the does vacuum and pressure, just make sure you check before hooking it to your brakes. I didn't. opps The kit itself is not bad, a lot of options for normal brakes, I have Willwood calipers and it has super small nipples so I had to use a tiny zip tie to keep the hose on and the air out. yet for my Ford Truck with normal size nipples it worked great. The only option I would like to see added is some kind of support for the cup, maybe a magnet or even a strap to hang it somewhere. I may hot glue a magnet to mine where I don't have to worry about the cup falling over. I'll update with a picture soon.
Recommended Products