Your cart is empty.
Your cart is empty.Product Description
It is front rider footboard insert compatible for Harley equipped with traditional-shaped rider footboards
Compatiblity
- Compatible for Ultra Limited FLHTK 2014-2024
- Compatible for Ultra Classic Tour Glide FLTCU 1989-1995
- Compatible for Ultra Classic Electra Glide FLHTCU 1989-2013
- Compatible for Ultra Classic Electra Glide - EFI FLHTCUI 1995-2006
- Compatible for Tri Glide Ultra FLHTCUTG 2014-2024
- Compatible for Tri Glide Ultra Classic FLHTCUTG 2009-2013
- Compatible for Switchback FLD 2012-2016
- Compatible for Street Glide Trike FLHXXX 2010-2011
- Compatible for Street Glide Special FLHXS 2014-2024
- Compatible for Street Glide FLHX 2006-2024
- Compatible for Softail Springer Classic FLSTSC 2005-2007
- Compatible for Softail Springer Classic - EFI FLSTSCI 2005-2006
- Compatible for Softail Deluxe FLSTN 2005-2017
- Compatible for Softail Deluxe - EFI FLSTNI 2005-2006
- Compatible for Softail Cross Bones FLSTSB 2008-2009
- Compatible for Road King Special FLHRXS 2017-2024
- Compatible for Road King FLHR 1995-2024
- Compatible for Road King Custom FLHRS 2004-2006
- Compatible for Road King Classic FLHRC 2007-2013
- Compatible for Road King Classic - EFI FLHRCI 1998-2006
- Compatible for Road King - EFI FLHRI 1996-2006
- Compatible for Road Glide Ultra FLTRU 2011-2019
- Compatible for Road Glide Special FLTRXS 2015-2024
- Compatible for Road Glide Limited FLTRK 2020-2024
- Compatible for Road Glide FLTRX 2015-2024
How to install the footboard rubber inserts?
- 1.Get the old footboards out.
- 2.Clean the metal foot pedal and all the mounting holes.
- 3.Drop right in with a little tire lube,dish soap or soapy water on the knobs and pull the ends through with small pliers.
RoadKing
Reviewed in the United States on August 11, 2024
2012 Road King - these floorboards fit perfectly with no modifications. Took maybe 5 minutes each side to replace. My original floorboards had the mounting rubbers broken, so I just ripped those off. I used some Simple Green solution to clean off the metal, then sprayed a little on the new rubber mounts. I also sprayed a little on each mounting hole, pushed down on the boards, then grabbed the mounts from underneath with a pair of pliers, pulling the mount through the hole. Great choice to replace the OEM boards!
David
Reviewed in the United States on August 11, 2024
Perfect fit thanks
Ray R Rust
Reviewed in the United States on May 15, 2024
good
glendale scott
Reviewed in the United States on November 12, 2024
The foot pads fit perfectly as replacement in my 2008 Fatboy. Recommend
Gerald Blikre
Reviewed in the United States on October 1, 2024
Not to hard to install. lube up the nubs that go through the floor boards and pull them in from the bottom of the floorboards with a small pliers. i used a small channel locks
Tres
Reviewed in the United States on August 7, 2023
There is a massive gap between board and bottom of rubber.Customer service is good though at resolving issue.
Chris
Reviewed in the United States on July 4, 2023
Look good and reduce vibration. Not easy to fit unless you know the trick! Grease each rubber stud , then wrap strong twine around it. Pass this through the hole - push down on the plate and pull the string through, this will set the studs correctly!
Recommended Products