Your cart is empty.
Your cart is empty.Product Description
8015 Dual Ball Bearing fan B07TZW378M
WINSINN Fan Production Process
Package Include:
2 x 8015 Sleeve bearings Fan - XH2.54 – 11.8in(300mm)
or
2 x 8015 Dual Ball bearings Fan - XH2.54 – 11.8in(300mm)
Rich
Reviewed in the United States on May 14, 2025
Smooth operation, quiet, and good air flow. Used for ventilation rather than cooling, but great product for a good price
Carlos
Reviewed in the United States on February 23, 2025
Material de calidad y el embalaje asegura que lleguen perfectos, ya los instale y tienen buena potencia, pueden enfriar un ordenador en menos de un minuto.
Andrea L DeVellis
Reviewed in the United States on January 4, 2025
This was a perfect motherboard fan replacement for my Anycubic Kobra 2 Pro!
Jim Clayton
Reviewed in Canada on August 14, 2024
They fit my printers well
Ripley
Reviewed in the United States on November 5, 2024
I purchased this to replace the stock main board cooling fan on my Sovol SV08 printer. The stock fan is much smaller and was very loud even when the printer wasn't printing. This fan, combined with a mount I found on Printables solved that problem and the machine is silent while not printing and much quieter during operation.
Customer
Reviewed in the United States on October 19, 2024
Direct replacement fan(s) for the Anycubic Photon Mono X. Six months and going strong and not too loud.
matteo
Reviewed in Italy on January 4, 2024
Ottimo
Raffaele Ballantini
Reviewed in Italy on April 4, 2023
Ventola di raffreddamento installata sulla scheda madre di una stampante 3d, ottima, poco rumorosa, con un'efficienza di tutto rispetto.
Weinert
Reviewed in Germany on October 10, 2022
Voll krass, wenn man da Strom darufgibt, dreht sich der Lüfter.Ich habe einen der beiden Lüfter in meinen Anycubic Vyper eingebaut, weil der vorhandene Lüfter seine Arbeit eingestellt hatte. Der Lüfter passt, und die Geräuschentwicklung ist durchaus im Rahmen des erträglichen.
PRNLM
Reviewed in the United States on April 10, 2022
It's surprisingly hard to find fans in this form factor. These are the right size for my application, so I rely on them. Just be aware that you'll get 4-6 months out of each fan at most.They do come with a connector attached—your best bet is to get ahold of the male side of the connector and solder that to your wires (rather than clipping and soldering the wires directly) so that you can swap them out in a minute or two.Then, just treat them like we used to treat light bulbs. Buy a bunch and switch them out as the bearings fail.
raymond callaway
Reviewed in the United Kingdom on September 10, 2021
Great value for money easy to install very quiet and cool like there supposed to will buy again when I need
Tim
Reviewed in the United States on November 22, 2021
Good price. Packaging was nice, came in a little plastic case. Seem sturdy and moves decent air. I use them attached to the housing of a power supply to keep it cool. Previous fans lasted a few years in a dusty shop environment, then crapped out. Same ones were no longer available, so went with these. They move a good amount of air for their size, however if noise is a factor for you, I'd steer clear. Being in a shop, It matters none to me. But if I had these elsewhere , it would drive me nuts. A very steady hum and slight wine.
Fri
Reviewed in the United States on July 22, 2019
I bought this fan in may, it's July and it's failing. It was very quiet at first and got noisier over time to a point it now spins slow unless you tap it a few times. Not good quality at all. UPDATE!! WInnsinn sent out 2 new fans and also mentioned that this brush less fan shouldn't be used more 12h continuously. The manufacturer of my 3d printer suggested to use this fan and it's obviously not the right fan for the job. Winnsinn did suggest to use this fan instead WINSINN 80mm Fan 24V Dual Ball Bearing DC Brushless Quiet Cooling 8015 80x15mm for PC. Great support from Winnsinn, increased my rating to 5 stars!
Recommended Products
$44.95
$ 20 .99 $20.99